Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Fort Wayne Homeowners Choose Gelco Chimney Cleaning
We provide independent Gelco chimney cleaning in Fort Wayne: creosote removal, Level 2 camera inspection, and cap and liner work on Gelco flexible liners, top-mount caps, and stainless caps. What sets our Gelco work apart is that we’re not tied to the brand, so we tell you plainly when a Gelco component is worth keeping and when it isn’t. We inspect it, clean it, and fix what we find with quality parts that fit Gelco equipment.
Fort Wayne Chimney Sweep handles sweeping, inspection, and repair as a chimney-only trade. Liner integrity isn’t optional. It’s the difference between a working fireplace and a fire hazard, and that’s the whole reason we carry Gelco knowledge alongside DuraFlex, HeatShield, Olympia Chimney, Famco, and Copperfield.
We are an independent service provider. We’re not affiliated with, authorized by, or a dealer for Gelco. Call (866) 589-6152. We answer 24/7.
Why Trust Fort Wayne Chimney Sweep for Your Gelco Chimney Cleaning?
Gelco is an Indiana-rooted manufacturer, and its stainless liners and caps are common in Fort Wayne’s older housing stock. Our technicians have up to experience and work on these components regularly, which means they know the real quirks rather than brochure copy. A flexible liner that was sized a little short of the flue top behaves differently from one that was wrapped and clamped properly, and that difference shows up in what collects at the connector.
We use quality parts that fit Gelco equipment. Where a replacement needs to keep the original fit and listing intact, we work with components made for that installation. For standard caps and non-structural fasteners, a reliable fitting part does the job without drama.
Warranty-safe service matters here. We don’t drill into, cut, or modify a listed liner to make a sweep easier. We clean it, inspect it with a camera, and photograph what we find so you can see the condition of your own flue. If something needs replacing, you’ll get the reason in plain terms and a written estimate before any work is booked.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common Gelco Chimney Cleaning Problems We Fix in Fort Wayne
Gelco flexible liners and caps are durable, but they’re installed in Fort Wayne chimneys that take a beating from hard northern Indiana winters. Here’s what we find most often, and why it happens.
- Liners sized short of the flue top. When a flexible stainless liner stops below the crown instead of reaching it, a gap opens at the top. Creosote and condensate collect there, and the smoke has somewhere to linger. It’s one of the most common installation issues we find, and it usually explains a smoke smell that gets worse on cool mornings.
- Insulation wrap that’s torn or degraded. Gelco insulated liner kits depend on that wrap staying intact. If it tears during installation or breaks down over time, the liner loses the benefit its UL 1777 listing is built around. Flue gases cool too fast and condense on the stainless, which is how corrosion starts from the inside.
- Caps and top plates loosening after freeze-thaw. Fort Wayne’s repeated freeze-thaw cycles work on the legs and fasteners of stainless caps and top plates. A cap that’s come loose lets water, debris, and wildlife into the flue. Sometimes the legs seize instead of loosening, which makes removal harder when the cap finally does need attention.
- Leaking joints at connectors and tees. The corrugated stainless on a Gelco liner has to be properly clamped and cemented where it meets the appliance connector or tee. When that connection was rushed, flue gases escape at the joint instead of going up the flue. You may notice a drip inside the firebox or a sharper smoke smell indoors.
- Rust-through on cap mesh and hardware. Condensate from a high-efficiency appliance sitting on the cap eats at lower-grade mesh and fasteners over the years. The cap looks fine from the ground until the mesh gives way.
A homeowner with a Gelco flexible liner often calls after noticing a drip inside the firebox or a stronger smoke smell on cool mornings. The usual culprit is a cap that’s come loose or a liner joint or connector leaking at the top plate. A qualified sweep typically runs a Level 2 camera inspection to check the liner top to bottom, confirms the cap and top plate are secure and correctly sized, then sweeps the flue to clear creosote buildup before re-securing or replacing the cap and re-sealing the connector.
That pattern is tied to Fort Wayne’s housing. The older core neighborhoods like West Central, Williams-Woodward, and Hoagland-Masterson are full of late-19th- and early-20th-century brick homes, and their chimneys were built for coal long before any liner went in. Original clay tiles spall and shift after a century of freeze-thaw, and some former coal flues were never lined at all. When a Gelco liner was later added to that kind of chimney, the fit and the top termination matter more than they would in a newer build. Sweep-and-inspect here is really a masonry-and-liner assessment, not just creosote removal.
Gelco Parts & Our Repair-vs-Replace Approach
Gelco liners and caps are proprietary enough that using genuine Gelco components on an existing Gelco installation keeps the fit and the listing intact. That’s our default when a structural part fails. Generic hardware is fine for non-structural fasteners and standard caps. We don’t claim to stock genuine Gelco parts. We specify what fits the installation and order what the job needs.
The repair-or-replace call follows the evidence. A cap, clamp, or connector that’s loose or rusted is a straightforward replace almost every time. A liner that’s cracked, torn in its insulation, or was sized short of the flue top is a different question. Patching a compromised liner rarely holds, and honest replacement usually costs less over time than chasing leaks. We show you the camera footage and photos first, and we say plainly when a repair can safely wait.
Call (866) 589-6152 for a free estimate on your Gelco liner or cap. We answer 24/7, with fast dispatch from 7am to 7pm.
Our Gelco Service Process – Step by Step
- 1
Diagnosis. We start with a Level 2 camera inspection of the full flue, from the appliance connection to the cap. On a Gelco liner we’re checking termination height, insulation condition, joint integrity at connectors and tees, and the cap and top plate.
- 2
Repair or install. If the cap or connector is the problem, we re-secure or replace it and re-seal the joint. If the liner itself has failed, we explain why and quote the reline in writing before anything is ordered.
- 3
Test. After the work, we confirm draft, check that the connector and tee joints are sealed, and verify the cap is secure and correctly sized for the flue.
- 4
Warranty. You get the photo report of what we found and what we changed, plus the documentation for any component we installed, so the paper trail stays with the chimney if you sell the house.
See the difference
Before
After
Before
After
Before
AfterGelco Products We Service & Install in Fort Wayne
We work on the Gelco components Fort Wayne homeowners actually have in their chimneys. That includes Gelco Flex-Liner flexible stainless relining kits, insulated flexible liner kits, Top-Mount multi-flue caps, and stainless chimney caps and top plates. Each one comes with its own failure pattern and its own right way to be serviced.
On the service side, creosote removal, cap replacement, and Level 2 inspection are the three jobs we do most on Gelco installations. A flexible stainless liner needs sweeping with the right tools so the corrugated wall isn’t damaged. A top-mount cap needs its legs and fasteners checked, not just its lid. And the annual inspection is what catches a short liner or a torn wrap before it turns into a bigger repair.
We Also Service These Brands
We carry six product lines because no two chimneys need the same fix. Alongside Gelco, we work with DuraFlex liner systems and HeatShield ceramic flue resurfacing, plus Olympia Chimney, Famco, and Copperfield components. HeatShield lets us resurface a damaged clay flue when relining isn’t yet necessary, and DuraFlex covers full relining when it is. Being multi-brand means the recommendation follows your chimney, not a single supplier.
FAQs – Gelco Chimney Cleaning Service in Fort Wayne
Yes, a Gelco flexible stainless liner can be swept, but it needs the right tools and technique so the corrugated wall and insulation wrap aren’t damaged. We use liner-safe brushes and inspect with a camera afterward to confirm nothing was disturbed. Call (866) 589-6152 to book a sweep.
No, a rattling top-mount cap usually means the legs or fasteners have loosened, not that the cap is finished. In Fort Wayne’s freeze-thaw cycles the legs can also seize, which makes re-securing harder but rarely means a full replacement. We check the cap and top plate, re-secure what’s sound, and only replace what’s failed. Call (866) 589-6152 for an assessment.
A liner installed short of the flue top often shows up as a smoke smell on cool mornings or creosote collecting at the connector, and only a camera inspection confirms it. From the ground you can’t see the termination height, so don’t guess from symptoms alone. We run a Level 2 inspection and show you the footage. Call (866) 589-6152 to schedule one.
No, an independent sweep doesn’t need Gelco authorization to clean, inspect, or repair a Gelco liner. We’re not affiliated with or authorized by Gelco, and we don’t claim to be. What matters is liner-safe technique, a camera inspection, and parts that fit the installation. Call (866) 589-6152 with questions about your liner.
No, waterproofing applied to the masonry around the flue doesn’t damage a Gelco stainless liner, as long as it stays off the liner itself and the cap area is left to breathe. Waterproofing the brick and crown is one of the ways to slow the freeze-thaw damage that cracks Fort Wayne chimneys in the first place. We can check the crown and cap while we’re there. Call (866) 589-6152 for a free estimate.
A standard Gelco chimney cleaning in Fort Wayne is typically quoted per job based on flue length, access, and how much creosote has built up, and the written estimate sets the final price. A camera inspection or cap replacement adds to that, and we quote it before booking. Nothing is recommended without camera evidence you can see for yourself. Call (866) 589-6152 for an exact quote. Estimates are free.
Book Your Gelco Service in Fort Wayne, IN
Whether it’s a sweep, a Level 2 inspection, or a cap that’s come loose, we handle the Gelco work in Fort Wayne from first look to final repair. Call (866) 589-6152 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Fort Wayne Chimney Sweep.